Kentix KSS-BASIC-2-B Manuel de service Page 29
- Page / 76
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5.4.7. System
System information
Shows the Firmware version number of the MultiSensor-LAN.
The actual firmware can be found on the Kentix Website in the section „Software & manuals“.
Test features
Test your E-Mail and SNMP settings via the two Buttons. The sending of E-Mails or traps is recorded in the
logbook.
Backup configuration
For backup-purposes the actual configuration of the MultiSensor can be downloaded here.
Restore configuration
Loads a previously created backup into the device and restarts it. The settings of the backup are directly
active afterwards.
Firmware-Update
Loads a firmware file (image.bin) into the MultiSensor and restarts it.
Restart
The MultiSensor-LAN can be restarted for testing or maintenance purposes. Note that the data recording is
suspended for the duration of the restart.
5.4.8. Switch alarm output 2
In the section Dashboard -> Control you have the possibility to switch the 2nd alarm output of the
MultiSensor-LAN. You can switch it for a specified period, by entering the time in seconds.
To switch the output permanently, enter a period of 0 seconds.
NOTE!
Pay attention to the relevant release notes of the downloaded update!
Page (04-2015, subject to change) kentix.com29
- User-Manual 1
- 1. Introduction and summary 4
- 2.1. CompleteSet 1 5
- 2.2. CompleteSet 2 5
- KMS-Door 6
- 2.4. Alarm-inputs 7
- 2.5. Relay contacts 7
- 2.6. Power supply 7
- KENTIX system-components 8
- 4. AlarmManager-BASIC/PRO 9
- 4.4. Configuration in 8 steps 10
- 4.6. Alarm zones 12
- 4.7.Quitting Alarms 12
- 4.8. User accounts 13
- OK! ARM ZONE 123 14
- SMS command 14
- SMS answer 14
- Alarm behavior 15
- E-Mail, SNMP & GSM 15
- General Settings 15
- Network monitoring 16
- Network Cameras 16
- I/O Modules 16
- SMS alarm forwarding 16
- 4.12.SMS gateway function 17
- 4.13.MIB for SNMP-Systems 18
- 5. MultiSensors 22
- 5.3. MultiSensor-RF 23
- 5.4. MultiSensor-LAN 24
- Dashboard 25
- 5.4.6. Users 28
- 5.4.7. System 29
- 5.4.8. Switch alarm output 2 29
- 5.5.6. Profile description 34
- 5.5.7. Testing the settings 34
- 5.6. MultiSensor-Rack 35
- 5.6.3. Overview connections 36
- Configuration 37
- 5.6.6. EnergySensor - Energy 38
- 5.6.8. Control 41
- 5.6.10. Users 43
- 5.6.11. System 43
- KENTIX system jack 44
- 7. KeyPad 48
- 7.1.Operation KeyPad 49
- 8. Enhancements 50
- Description 55
- Application examples 55
- AlarmManager-BASIC/PRO 56
- Alarm sirene 56
- 8.6.1. Configuration 57
- 8.7. Kentix IO-Modules 58
- 9.1. The Profile menu 60
- 9.2. AlarmManager 60
- 9.3. SMS Control 61
- 10. Data sheets 62
- 10.8.Data sheet KeyPad (KKP) 69
- Function 74
- Place of installation 75
- 12. Support 76
Produits connexes et manuels pour Systèmes d'alarme de sécurité Kentix KSS-BASIC-2-B
(1 pages)AEG E5701-4-ANORDIC manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro míchačky / kuchyňské roboty AEG E5701-4-ANORDIC.
Poskytujeme 1 manuály pdf AEG E5701-4-ANORDIC ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels